Vintage Tube Amp

Sparkly highs and tons of bottom! New bugera 12ax7 preamp tube and new jj el84 output tube.

Even the multi-section electrolytic filter capacitor (the tubular aluminum can visible on top of chassis) is brand new. This console Maggie has been modified to be a stand alone, fully integrated audio amplifier. It not only includes the original 9302 power amp, but the original Magnavox pre-amp as well, with all the associated controls, including volume. It has been thoroughly tested to ensure that all operating parameters are within proper specifications. All tubes are either brand new, or new old stock (NOS) and test accordingly. As is usually the case, the console’s pre-amp and tone controls (including the volume), were located inside the tuner chassis, not the amplifier chassis. Nlike most typical console amplifier restorations, this 9302 has been reunited with it’s matching pre-amp circuit formally located in the tuner. Since the original Maggie 9302 chassis is oversized and already had an empty tube socket hole labeled “6EU7″ (for use in other equipment that Magnavox manufactured), the extra pre-amp tube, controls and circuitry, were easily accommodated. It’s all “under the hood” of this now fully integrated, high fidelity, stereo tube amplifier. This beautiful Maggie is plug and play and ready to go. Just connect the speakers of your choice. The 9302 was designed for 4 ohm speakers, but works very well with a pair of 8 ohm, high efficiency speakers (above 90dB), like Klipsch, or even a quad set of 8 ohm speakers where each pair is connected in parallel (4 ohms total) to each stereo channel. This fully integrated Magnavox 9302 not only sounds great, but it looks great too. A front panel plate and bottom panel have also been custom fabricated. All controls use a standard 1/4 diameter shaft, so you can inexpensively change the knobs to whatever style you like. The professional restoration of this Magnavox 9302 includes the following repairs, upgrades and modifications. Remove 12 pin molex connector (umbilical connection to console tuner). Rewire power supply circuit to allow amplifier to operate as a stand alone unit. “Across the line” filter capacitor replaced with 2 new Y2X1 safety capacitors. Modified chassis to remove unused terminals and accommodate new switches, connectors and controls. Grounded 3 prong IEC connector installed at rear of chassis (3 wire grounded power cord is provided). Line fuse holder installed (2A slow blow) at rear of chassis. Install green neon pilot lamp at front panel of chassis. Eight (4 pairs) gold, rear panel mount, RCA audio input connectors mounted at rear of chassis. Four (2 pairs) gold, 5 way, speaker binding posts mounted at rear of chassis. Added a third 9 pin tube socket (for pre-amp tube) into pre-existing empty hole in chassis. Replaced one existing 9 pin tube socket. Integrated entire 6EU7 pre-amp circuit from console tuner, including. 6EU7 pre-amp tube. Volume control mounted to front panel of chassis (with K4 tone compensation circuit). Treble control mounted to front panel of chassis. (with K5 tone compensation circuit). Bass control mounted to front panel of chassis. (with K6 tone compensation circuit). Installed illuminated power switch on top of chassis. Installed a 4 position rotary selector switch mounted to front panel of chassis. Replaced multi-section electrolytic capacitor can with brand new CE Manufacturing Mallory FP type can. Install F & T multi-section tone capacitor into new pre-amp circuit. Replaced all paper capacitors with metal film tone capacitors. Tested all resistors and replaced any that were out of tolerance. Rewire as needed to create a fully integrated, multi-input amplifier. Fabricate wooden side boards and secure to chassis. Fabricate custom face plate and secure to front panel. Mount left and right stainless steel side rails, using four (4) threaded rods. Fabricate and Install chassis bottom, securing with four (4) stainless steel feet (1 standoff). Trim potentiometer shafts and mount new control knobs on all controls. Replace all eight (8) vacuum tubes. (1) 5U4GB rectifier tube (NOS American made). (3) 6EU7 amplifier tubes (NOS American made). (4) 6BQ5/EL84 beam power tubes (brand new, quad matched Sovtek). This Maggie is a rare beauty that doesn’t come up for sale very often. Don’t let it get away. A lot of man hours have gone into this amplifier and everything used in the restoration is of the highest quality. A schematic diagram will be provided. If you have any questions, please don’t hesitate to contact me. The item “VINTAGE MAGNAVOX 9302 TUBE AMP, RESTORED & FULLY INTEGRATED With PREAMP INSTALLED” is in sale since Sunday, June 30, 2019. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “chip2020″ and is located in Sarasota, Florida. This item can be shipped to United States.

• Model: 9302-00
• Modified Item: Yes
• Country/Region of Manufacture: United States
• Type: Tube Amplifier
• MPN: Does Not Apply
• Modification Description: Modified to be a fully integrated amplifier by installing pre-amp and controls.
• Brand: Magnavox