Vintage Tube Amp

Even the multi-section electrolytic filter capacitor (the tubular aluminum can visible on top of chassis) is brand new. This console Maggie has been modified to be a stand alone, fully integrated audio amplifier. It not only includes the original 9302 power amp, but the original Magnavox pre-amp as well, with all the associated controls, including volume. It has been thoroughly tested to ensure that all operating parameters are within proper specifications. All tubes are either brand new, or new old stock (NOS) and test accordingly. As is usually the case, the console’s pre-amp and tone controls (including the volume), were located inside the tuner chassis, not the amplifier chassis. Nlike most typical console amplifier restorations, this 9302 has been reunited with it’s matching pre-amp circuit formally located in the tuner. Since the original Maggie 9302 chassis is oversized and already had an empty tube socket hole labeled “6EU7″ (for use in other equipment that Magnavox manufactured), the extra pre-amp tube, controls and circuitry, were easily accommodated. It’s all “under the hood” of this now fully integrated, high fidelity, stereo tube amplifier. This beautiful Maggie is plug and play and ready to go. Just connect the speakers of your choice. The 9302 was designed for 4 ohm speakers, but works very well with a pair of 8 ohm, high efficiency speakers (above 90dB), like Klipsch, or even a quad set of 8 ohm speakers where each pair is connected in parallel (4 ohms total) to each stereo channel. This fully integrated Magnavox 9302 not only sounds great, but it looks great too. A front panel plate and bottom panel have also been custom fabricated. All controls use a standard 1/4 diameter shaft, so you can inexpensively change the knobs to whatever style you like. The professional restoration of this Magnavox 9302 includes the following repairs, upgrades and modifications. Remove 12 pin molex connector (umbilical connection to console tuner). Rewire power supply circuit to allow amplifier to operate as a stand alone unit. “Across the line” filter capacitor replaced with 2 new Y2X1 safety capacitors. Modified chassis to remove unused terminals and accommodate new switches, connectors and controls. Grounded 3 prong IEC connector installed at rear of chassis (3 wire grounded power cord is provided). Line fuse holder installed (2A slow blow) at rear of chassis. Install green neon pilot lamp at front panel of chassis. Eight (4 pairs) gold, rear panel mount, RCA audio input connectors mounted at rear of chassis. Four (2 pairs) gold, 5 way, speaker binding posts mounted at rear of chassis. Added a third 9 pin tube socket (for pre-amp tube) into pre-existing empty hole in chassis. Replaced one existing 9 pin tube socket. Integrated entire 6EU7 pre-amp circuit from console tuner, including. 6EU7 pre-amp tube. Volume control mounted to front panel of chassis (with K4 tone compensation circuit). Treble control mounted to front panel of chassis. (with K5 tone compensation circuit). Bass control mounted to front panel of chassis. (with K6 tone compensation circuit). Installed illuminated power switch on top of chassis. Installed a 4 position rotary selector switch mounted to front panel of chassis. Replaced multi-section electrolytic capacitor can with brand new CE Manufacturing Mallory FP type can. Install F & T multi-section tone capacitor into new pre-amp circuit. Replaced all paper capacitors with metal film tone capacitors. Tested all resistors and replaced any that were out of tolerance. Rewire as needed to create a fully integrated, multi-input amplifier. Fabricate wooden side boards and secure to chassis. Fabricate custom face plate and secure to front panel. Mount left and right stainless steel side rails, using four (4) threaded rods. Fabricate and Install chassis bottom, securing with four (4) stainless steel feet (1 standoff). Trim potentiometer shafts and mount new control knobs on all controls. Replace all eight (8) vacuum tubes. (1) 5U4GB rectifier tube (NOS American made). (3) 6EU7 amplifier tubes (NOS American made). (4) 6BQ5/EL84 beam power tubes (brand new, quad matched Sovtek). This Maggie is a rare beauty that doesn’t come up for sale very often. Don’t let it get away. A lot of man hours have gone into this amplifier and everything used in the restoration is of the highest quality. A schematic diagram will be provided. If you have any questions, please don’t hesitate to contact me. The item “VINTAGE MAGNAVOX 9302 TUBE AMP, RESTORED & FULLY INTEGRATED With PREAMP INSTALLED” is in sale since Sunday, June 30, 2019. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “chip2020″ and is located in Sarasota, Florida. This item can be shipped to United States.

• Model: 9302-00
• Modified Item: Yes
• Country/Region of Manufacture: United States
• Type: Tube Amplifier
• MPN: Does Not Apply
• Modification Description: Modified to be a fully integrated amplifier by installing pre-amp and controls.
• Brand: Magnavox

Vintage 1960s Dynacord Echocord Super S65 Tube Preamp Tape Echo Machine + 6 Tapeloops + 3 Adapter Cables + + Power Cord + Operator’s Manual Excellent Condition. Ich biete hiermit mein gut 50 Jahre altes Band-Echo/-Hall Effektgerät Echocord Super 65 von Dynacord zur Auktion an. Es ist ein absoluter Klassiker und noch ein Vollröhrengerät aus der Echocord-Serie. Das Echocord hat einen integrierten 5-Kanal-Mixer (3 x Instrument + 2 x Mikro) mit jeweils Volume und Tone-Reglern. Das Gerät arbeitet mit 1x Löschkopf, 2x Wiedergabeköpfe und 3x Aufnahmeköpfe. Folgende Echo/Hall Funktionen sind einstellbar: Taste Aus/Off (Ein/Ausschalten des Echocord) Taste Nachall Aus/Reverb off (Ein/Ausschalten des Effekts) Taste Adagio (langsame Bandgeschwindigkeit, für lange Echos) Taste Presto (schnelle Bandgeschwindigkeit, für kurze Echos) Taste Echo1 (Einstellung kurze Echos) Taste Echo2 (Einstellung mittlere Echos) Taste Echo3 (Einstellung lange Echos) Taste Nachall/Reverb (Alle Köpfe sind aktiv, mit Potis einzeln einstellbar). Nachhallstärke/Reverb Control (Effektlautstärke) Nachhalldauer/Reverb duration (Feedback) Klangreglung/Tone control (Effekttoneinstellung). Die Tasten Echo1 bis Echo3 können auch kombiniert gedrückt werden. Darüber hinaus gibt es noch eine Buchse für einen Fußschalter zur Effekt Ein- bzw. Ausschaltung sowie eine Buchse zum Anschluß der Echofernregelung. Der Sound des Echocord 65 ist wie man ihn von einem echten Vintage-Gerät erwartet: Warm, mit musikalischen Charme und analoger Charakterstärke. Vor allem sollte man nicht vergessen, dass man den Echocord natürlich auch als Röhren-Preamp nutzen kann. Ich habe meine US-Strat direkt an den Echocord S65 angeschlossen und hatte somit eine Vorstufe mit einem warmen leicht angezerrten Röhren-Overdrive Sound (mit oder ohne Echoeffekt) extrem bluesig!! Mit dabei sind Ersatz-Tonbandschleifen! Das Echocord ist für sein Alter in einem technischen und optischen sehr guten und sauberen Zustand. Ich liefere Dynacord Echocord Super 65 komplett mit. Danke für Euer Interesse. This is my approx. 50 years old tube delay unit Echocord Super 65 from Dynacord.. Its an absolute classic machine, staffed with excellent vintage tube technology! The Echocord features an in-built five channel mixer (3x instrument + 2x microphone) with one volume and one tone pots each The unit wokrs with 2x playback heads and 3x record heads.. The following funcions are available: Button on/off Button Reverb on/off Button Adagio (slow motor mode) Button Presto (fast motor mode) Button Echo1 (fast echo effect) Button Echo2 (medium echo effect) Button Echo3 (slow echo) Button Reverb (all heads are active). Reverb Intensity Reverb-Feedback Tone control (delay effect). The buttons Echo1 to Echo 3 can also be pushed in combination. Furthermore you will find a plug for footswitch in order to switch the effect on/off and a plug for the echo remote-control. The sound of this wonderful Echocord is like a real vintage tape echo unit : Warmth, charme and analog character strength! And dont forget, you can use this unit as a fantastic tube preamp. I used it with an old Stratocaster and Ive got a warm smooth overdrived tube sound. With and without an echo effect. The Dynacaord Echocord S65 works fine and is in excellent and clean condition. The Dynacord Echocord machine comes completely with the follwing accessories. Suitable power cord (US or EU – just let me know) Operators Manual (paper copy) [Kurzbeschreibung (Kopie)] Output-adapter DIN/TRS socket (high output) Output-adapter DIN/TRS socket (low output) Input-adapter DIN/TRS socket Schematics (paper copy) 6 tape echo loops. Sounds incredible and unique – It doesnt get any better than this. Any questions please do not hesitate to contact me. Vintage 1960s Dynacord Echocord S65 Tube Tape Echo Delay Preamp 110-240V TOP. This is a private listing. All sales are final. Viel Spaß beim Bieten! Porto/Verpackung der Käufer – Ebaykosten übernehme ich. Persönliche Abholung ist natürlich nach Absprache auch möglich. Dies ist ein Privatverkauf – Unter Ausschluss jeglicher. Ich übernehme keinerlei Garantie und keinerlei. Besondere Versandwünsche bitte mitteilen. Fragen sind vor Abgabe eines Gebotes zu stellen. Abgabe des Gebotes erklären Sie sich ausdrücklich damit. Einverstanden , auf die gesetzliche Sachmängelhaftung bei. Gebrauchtwaren völlig zu verzichten. The item “Dynacord Echocord S65 Vintage 1960s Tube Tape Echo Delay Preamp 110-240V TOP” is in sale since Thursday, August 1, 2019. This item is in the category “Musikinstrumente\Gitarren & Bässe\Zubehör\Effektgeräte\Delays, Echos & Reverb Effekte”. The seller is “tjen48″ and is located in Ennepetal. This item can be shipped worldwide.

• Technologie: Analog
• Marke: Dynacord
• Modell: S65
• Herstellernummer: Echocord Super 65
• Produktart: Tape Echo
• Herstellungsland und -region: Deutschland
• Passend für: Keyboards

Dies ist ein Vintagetools Custom Rack (VTCR) bestückt mit einem der legendären TAB, Siemens oder Telefunken V72 Röhrenverstärker. Das abgebildete Modul ist ein Beispiel. Marke und Seriennummer können abweichen! Das Gehäuse ist in 19 2HE gebaut und sehr hochwertig gefertigt. Das Rack beinhaltet folgende Extras. Phantomspannungsmodul mit 230V Eingang und stabilen, langsam ansteigenden 48V DC Ausgangsspannung für Kondensatormikrofone. Das langsame Ansteigen schont den V72 Eingangsübertrager. Verstärkungsregelung in 11-Schritten von 0dB bis 34dB. Umgesetzt mit einem vergoldeten Stufenschalter. Eigens für dieses Rack hergestellter Netzeingangstrafo mit 238V/115V Eingangsspannung (nach Wunsch und Kundenangabe) und stabiler 220V Ausgangsspannung. Die Geräte der V72 Serie wurden damals mit 220V Netzspannung betrieben, während heutige Stromnetze oft 235V – 239V liefern. Die Drosselung auf 220V schon die Röhren und sorgt für einen verzerrungsärmeren Sound, bzw. Den Originalsound des Gerätes. Bitte beachten Sie auch unseren. Youtube/vintagetools Kanal mit weiteren Informationen zu analoger Rundfunktechnik! Vintagetools VTCR custom including one V72 tube mic preamp. It includes a ramped phantom power module, 11-step gain pad via rotary switches with resistors regulating the ain from 0DB to +34dB and a 238V/115V AC input to 220V AC output power transformer. This rack will be custom made after your order. Please allow 2 week buildtime. More information on the V72 can easily be found on our website. The tube module shown on the pictures is a sample. Please also check our youtube/vintagetools video channel with more infos! The item “Siemens V72 im vintagetools VTCR Custom Rack tube mic preamp” is in sale since Thursday, April 11, 2019. This item is in the category “Musikinstrumente\Pro-Audio Equipment\Vorverstärker”. The seller is “vintagetoolsde” and is located in 64546 Mörfelden. This item can be shipped worldwide.

• Herstellernummer: nicht zutreffend

All tubes are vintage tubes and included. I also think the preamp is in original form, no modifications. I plugged it in for testing and both channels worked and produced good music. I found the Spare (and probably other) input has one channels dropped. I tried “Special” and then OK. So, this preamp may need some cleaning and adjustment before daily use; just like all vintage electronics. Physical condition is pretty good for the age. Some discoloration/wear/scratches, as shown on the pictures. All knobs are original. The item “Dynaco PAS-2 Tube Preamplifier Preamp for ST-70 Amp Works, All Vintage Tubes” is in sale since Wednesday, February 27, 2019. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Preamps & Tube Preamps”. The seller is “timekinetics” and is located in Oakland, California. This item can be shipped worldwide.

• Brand: Dynaco
• Model: PAS-2

Preowned ADA MB-1 MIDI Programmable preamp. The item “VTG ADA MB-1 Midi Programmable Bass Guitar Tube Rack Preamp AMP 80 Stereo Effect” is in sale since Saturday, January 5, 2019. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “ebass08″ and is located in North Adams, Massachusetts. This item can be shipped to United States.

• Brand: ADA

Vintage Very Rare 1963 Schaller Echo-Sound Tube Preamp Disc Echo Machine + Adapter Cable + Power Cord + Operator’s Manual Excellent Condition. Ich biete hiermit mein gut 55 Jahre altes Röhren – Echo/-Hall Effektgerät Echo-Sound von Schaller zum Verkauf an. Es ist ein absoluter sehr seltener Klassiker und noch ein Vollröhrengerät von Schaller. Das Echo wird durch eine magnetisierbare Trommel (aufgedampfte Fe2O3 Schicht), an der 4 Tonköpfe und ein Löschkopf positioniert sind, erzeugt. Also gibt es hier nicht, wie bei den Tape-Echogeräten, einen Bandverschleiß. Der Echo-Sound hat einen integrierten 3-Kanal-Mixer mit jeweils 1 Schiebeschalter für Echo on/off. Folgende Echo/Hall Funktionen sind einstellbar: Echozeit kurz Echozeit mittel Echozeit lang Echozeit kurz + mittel Echozeit kurz + lang Echostärke (Echolautstärke) Nachhall (Feedback) Gesamtlautstärke. Folgende Anschlüse stehen zur Verfügung: Input I für Instrumente Input II für Instrumente z. Gitarre Input III niederohmiger Eingang oder Input III hochohmiger Eingang Output – Buchse Anschluß für Fernregler Technische Daten: Abmasse: 370 x 135 x 200 mm / 14.6 x 5.3 x 7.9 inch Gewicht: 6.9 kg / 15 lb 3.2 oz (15.198 lb) Gehäuse-Material: Metall Input I: ca. 1 MOhm Input II: ca. 1 MOhm Input III: ca. 200 Ohm oder Input III: ca. 500 KOhm Echofrequenzgang bis ca. 3 5 kHz Das Echo-Sound arbeitet sowohl mit 230 Volt als auch mit 120 Volt, umschaltbar an der Rückseite des Gerätes. Der Sound des Echos-Sound ist wie man ihn von einem echten Vintage-Gerät erwartet: Warm, mit musikalischen Charme und analoger Charakterstärke. Achtung: Für jemand, der ein glasklares Digital-Echo er wartet, ist dieses Vintage Gerät aber nicht das Richtige! Vor allem sollte man nicht vergessen, dass man das Gerät natürlich auch als Röhren-Preamp nutzen kann. Ich habe meine US-Strat direkt an den Schaller Echo – Sound angeschlossen und hatte somit eine Vorstufe mit einem warmen leicht angezerrten Röhren-Overdrive Sound (mit oder ohne Echoeffekt) extrem bluesig!! Der Schaller Echo-Sound ist für sein Alter in einem technischen und optischen sehr guten und sauberen Zustand. Zwei Tonköpfe wurden vor einiger Zeit mal gegen original Binson- Tonköpfe getauscht. Ich liefere Gerät komplett mit. Danke für Euer Interesse. This is my approx. 55 years old tube delay unit Echo-Sound from Schaller.. Its an absolute classic machine, staffed with excellent vintage tube technology! The echo is produced through a magnetizable drum (evaporated Fe2O3 layer), where 4 heads and one erase head are positioned. So no tape wear, like in the tape echo machines. The unit has a built-in 3-channel mixer with a slide switch for echo on / off. The following Echo functions are available: Echo time short Echo time medium Echo time long Echo time short + medium Echo time short + long Echo strength (echo volume) Reverberation (feedback) Full volume The following connections are available: Input I for instruments Input II for instruments, eg. Guitar Input III low-impedance input or Input III high-impedance input output jack Connection for the remote control Technical specifications: Dimensions: 370 x 135 x 200 mm / 14.6 x 5.3 x 7.9 inches Weight: 6.9 kg / 15 lb (15.198 lb) Housing material: metal Input I: approx. 1 MOhm Input II: approx. 1 MOhm Input III: about 200 ohms or Input III: approx. 500 kOhm Echo frequency response up to approx. 3 – 5 kHz The echo sound works with both 230 volts and 120 volts switchable on the back of the device. The sound of this wonderful Schaller Echo-Sound is like a real vintage echo unit : Warmth, charme and analog character strength! But attention: For someone who is expecting a crystal clear digital echo sound, this vintage device is not the right one! And dont forget, you can use this unit as a fantastic tube preamp. I used it with an old Stratocaster and Ive got a warm smooth overdrived tube sound. With and without an echo effect. The Schaller Echo – Sound works fine and is in excellent and clean condition. Two heads have been exchanged by original Binson heads some time ago. The Echo-Sound unit comes completely with the follwing accessories. Suitable power cord (US or EU – just let me know) Description (paper copy) Output-adapter DIN/TRS socket Schematics (paper copy). Any questions please do not hesitate to contact me. Vintage Very Rare 1963 Schaller Echo – Sound Disc Tube Delay Preamp 110-240V TOP. This is a private listing. All sales are final. Viel Spaß beim Bieten! Porto/Verpackung der Käufer – Ebaykosten übernehme ich. Persönliche Abholung ist natürlich nach Absprache auch möglich. Dies ist ein Privatverkauf – Unter Ausschluss jeglicher. Ich übernehme keinerlei Garantie und keinerlei. Besondere Versandwünsche bitte mitteilen. Fragen sind vor Abgabe eines Gebotes zu stellen. Abgabe des Gebotes erklären Sie sich ausdrücklich damit. Einverstanden , auf die gesetzliche Sachmängelhaftung bei. Gebrauchtwaren völlig zu verzichten. The item “Vintage Very Rare 1963 Schaller Echo Sound Disc Tube Delay Preamp 110-240V TOP” is in sale since Thursday, February 14, 2019. This item is in the category “Musikinstrumente\Gitarren & Bässe\Zubehör\Effektgeräte\Delays, Echos & Reverb Effekte”. The seller is “padawan0151″ and is located in Ennepetal. This item can be shipped worldwide.

• Marke: Schaller
• Technologie: Analog
• Herstellernummer: Echo-Sound
• Passend für: Vocals
• Produktart: Echo
• Modell: Echo-Sound
• Herstellungsland und -region: Deutschland

Very rare Pair Quad II amplifier + QUad 22 preamplìier. We checked and replaced caps, resistor needed ect: filter power caps, coupling caps… They are perfect working and run so quietly. 6 tubes EF86 Mullard vintage, 2 ECC83/12ax7 Telefunken vintage, 2 GZ32 Mulard vintage, 2 KT66 Genalex vintage, 2 Túngol new. All tubes checked and strong. I can replace matched pair KT66 New Tungsol if you want. Please refer all the pictures carefully or you have any question, please let me know. But when in use if they have any problem, you can send it back to free fix. Thank you for your attention. The item “Vintage Quad II tube amplifier + QUAD 22 tube preamp England” is in sale since Saturday, February 9, 2019. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “atlusllc” and is located in Duluth, Georgia. This item can be shipped to United States, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Bahrain, Croatia, Malaysia, Brazil, Panama, Viet nam, Uruguay.

• Brand: Quad
• Type: Power Amplifier
• Model: ii
• Country/Region of Manufacture: United Kingdom

Awesome 1st Quality 100% Authentic. My reputation and feedback speaks for itself! VTG ADA MP-1 Midi Programmable Tube Guitar Preamp. The last pictures show the other ADA and Marshall Rack mounts available in my other auctions. ADA MP-1 Midi Programmable Tube Guitar Preamp Processor Overdrive, Chorus. All the wide assortments of distortions, overdrives and cleans to give you every sound from the 80′s that you would need for hair metal. The Chorus effects on this unit are angelic 80′s sounds. The ADA Mp-1 All knobs are intact. All program buttons work. The mounting tabs are in good condition. The memory battery and tubes has been tested and everything is good. The MP-1 has been reset to factory settings and ready to rock. The ADA MP-1 has overdrive, chorus, flange, and compression effects. This preamp was very popular in the 80s and gives you the 80s sounds. Skid Row, Extreme and White Lion. Paul Gilbert, George Lynch and many others swear by ADA setups. All tested and ready to go. I also have a VTG ADA and. Marshall in my other auctions. A/DA MP-1 Guitar Preamp is a MIDI-controlled rack-mountable effects unit featuring overdrive, chorus and EQ functionality. The most tonally flexible and technologically advanced guitar amplification. Your MP-1 will store 128 programs of exactly the right tone. Matter what kind of music you play. The MP-1 features a unique Tri-State Voicing selection that allows you to choose. Between Distortion Tube, Clean Tube, or Solid State circuits for each program. EQ points were designed to replicate the sound of Fender and Marshall, but the. Presence control surpasses the range offered by either. The stereo Chorus utilizes analog circuitry which complements the warmth of tubes. To give you the best possible sound. Nuno Bettencourt, Paul Gilbert. Unique Tri-State Voicing option for choice of Clean Tube. Distortion Tube, or Solid State circuit for each program. Two low noise 12AX7 A/7025 tubes. Three programmable gain controls for each program. Four band programmable EQ including 16dB boost/cut for bass and treble. Fully programmable stereo chorus and doubler. Programmable effects loop with adjustable send/receive level. Stereo headphone jack with level control. Stereo outputs switchable from line level (to mixing board) to instrument level (to guitar amp). 1/4 instrument level input jack on front panel for easy access. Active balanced input on rear panel for mixing boards. Output level knob for fast volume adjustment without affecting tone. Programmable compression level in Solid State mode. Received MIDI program numbers are re-assignable (mapable) to any MP-1 memory number. MIDI In, Out and Thru. Selectable MIDI channel including ALL channels (OMNI) and no channels (OFF). Lexan membrane switch front panel replaces pots. No contamination from dust or liquids. Optional MC-1 MIDI CONTROLLER footswitch provides instant access to any program for on-stage control. Self-diagnostics check unit during power up. Instantaneous logic-controlled FET switching. EPROM updates will be available for future system expansion. State-of-the-art software implementation including SYSEX and MIDI Time Code for computer controlled applications. You will not be sorry. Incredible pow at a fair price. Grab it up today! There can’t be many of these around. I will carefully pack this item in foam peanuts; tissue and bubble wrap to insure a safe arrival. Don’t miss out on this one; it may be a l-o-n-g time before another one turns up. I have other items, Etc. It is a good investment as it will provide many years of enjoyment service and be worth more in the future. A picture really is worth a thousand words! (Photos are of actual item) Thanks for looking! I hope this is just what you are looking for. I have a lot of items that will probably take me a year to list so keep watching and thank you, cooldady-0. If youre cool, welcome to a world of fun and interesting items. YOUR COMPLETE SATISFACTION IS MY MAIN GOAL. SO PLEASE REMEMBER IF THERE ARE ANY PROBLEMS NOT MENTIONED, OR YOUR UNHAPPY WITH YOUR ITEM. CHECK OUT MY FEEDBACK FOR ALL OF MY SATISFIED CUSTOMERS OVER THE PAST 20 YEARS. You will love this. ITEMS Meticulously wrapped in foam and bubble wrap!!! To NYS Residents only. The item “VTG ADA MP-1 Midi Programmable Guitar Tube Rack Preamp AMP 80s excellent 12AX7 2″ is in sale since Thursday, December 27, 2018. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “cooldaddy-0″ and is located in Batavia, New York. This item can be shipped worldwide.

• Brand: ADA

This 1956 Magnavox mono tube amplifier model 128E includes its matching phono preamp control and. The original L-shaped wooden control panel overlay from the Magnasonic phonograph console it came from. The big 128E amp contains four 6V6 tubes and two 5Y3GT tubes, as well as a 12AX7. The original power indicator light is still wired in. The preamp contains a single 6AV5 tube and has three knobs that control volume, treble, and bass. The bass switch also turns the power on and off. Preamp has a mono phono input and a hard-wired rca cord that connects to the main amplifier. The small 12AX7 and 6AV5 tubes are from Sylvania and Motorola, the rest are all Magnavox brand. The amp platform measures 13 inches x 11 inches x 2 1/8 inches (side mounting fins are 3/4 inch each). The preamp box measures 5.5 inches x 1.75 inches x 2.5 inches. The item “MAGNAVOX TUBE AMPLIFIER 128E with PHONO PREAMP CONTROL 125C VINTAGE 1956 6V6 AMP” is in sale since Tuesday, July 24, 2018. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “atomicspacejunk88″ and is located in Snellville, Georgia. This item can be shipped worldwide.

• Country/Region of Manufacture: United States
• Type: Integrated Amplifier
• Brand: Magnavox

Tested and in working condition. Due to the age it will probably need new capacitors. The controls are also a bit scratchy. It should be considered a project as with all vintage audio gear that has not been reconditioned. The item “Vintage Audio Dynaco PAS Audiophile Tube Audio Preamp Pre Amp Amplifier USA” is in sale since Tuesday, September 25, 2018. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Preamps & Tube Preamps”. The seller is “globalmarket3216″ and is located in Perkasie, Pennsylvania. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Brazil, Chile, Colombia, Costa rica, Panama, Trinidad and tobago, Guatemala, Honduras, Jamaica.

• Brand: Dynaco
• Country/Region of Manufacture: United States
• Model: PAS
• Type: Preamplifier
• UPC: Does Not Apply