Vintage Tube Amp

GIBSON GA-15RVT VACUUM TUBE GUITAR AMP. This Gibson GA-RVT guitar amp works and sounds great. The amp is used and is approximately 65 years old with normal signs of wear and tear but not any mistreatment. The amp puts out around 15 watts. The circuit was refurbished. New filter capacitors were installed. Out of tolerance resistors were replaced. All capacitors in the signal path were replaced with modern and fresh capacitors. Everything is there with the amp such as the original working foot pedal, working reverb and tremolo, a new 10″ “Real Vintage speaker that was a major improvement over the original, worn-out factory speaker. The tolex is heavy-duty and shows some normal wear for a 60+ year-old amp. The handle was built to last and is very robust. The back brace is missing as well as the insert on the on/off knob. All the vacuum tubes are US made except one and all tested and sound great. There are two Sylvania 6BQ5/EL84 power tubes, an RCA 5963 (12AU7 equivalent) and two 6EU7 preamp tubes, one RCA and one Mullard. It’s a great amp ready to go for many more years. More to other locations. The item “GIBSON GA-15RVT VACUUM TUBE AMP VINTAGE US MADE 15 Watt GUITAR AMPLIFIER” is in sale since Friday, October 9, 2020. This item is in the category “Musical Instruments & Gear\Vintage Musical Instruments\Vintage Guitars & Basses\Guitar Amplifiers”. The seller is “dougcaster” and is located in Oklahoma City, Oklahoma. This item can be shipped to United States, Canada, United Kingdom, China, Mexico, Germany, Japan, Brazil, France, Australia, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Greece, Portugal, Cyprus, Slovenia, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Austria, Bahamas, Israel, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Costa rica, Panama, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.

• Model: GA-15RVT
• Modified Item: Yes
• Country/Region of Manufacture: United States
• Modification Description: The amp circuit was refurbished and sound great. The amp’s filter caps were replaced as well as the caps in the signal path and out of tolerance resistors.
• Brand: Gibson

AS YOU CAN CLEARLY SEE IN THE PICS THIS GUITAR AMP IS IN VERY GOOD CONDITION. THIS AMP WAS PART OF A GROUP ORDERED FROM GIBSON GUITARS BY THE FORBES MUSIC COMPANY IN BIRMINGHAM, AL. THE ORIGINAL FORBES MUSIC BRONZE LOGO IS STILL INTACT AND ON THE AMP CABINET. THEY WERE WERE ORIGINALLY DESIGNED FOR ORGANS BUT ALSO MAKE A FINE GUITAR AMP. THE ORIGINAL TOLEX AND SPEAKER GRILL CLOTH HAD TO BE REMOVED DUE TO A PREVIOUS OWNER SPRAY PAINTING IT WITH NUMEROUS COATS OF GLOSS BLACK PAINT THAT COULD NOT BE REMOVED. I’VE HAD THE AMP RECOVERED IN NEW VINTAGE CORRECT TWEED TOLEX, NEW VINTAGE CORRECT OXBLOOD SPEAKER GRILL CLOTH WAS INSTALLED, THE ORIGINAL JENSEN 15 SPEAKER WAS PROFESSIONALLY RECONED AND I RECENTLY HAD IT SERVICED BY A PROFESSIONAL AMP TECNICIAN WHO REPLACED THE POTS, FILTER CAPACITORS AND A FEW RESISTORS AND ELECTROLYTIC CAPACITORS. THE AMP STILL HAS ALL ITS ORIGINAL TUBES AND ORIGINAL TWO PRONG POWER CORD. BASICALLY THIS IS THE EQUIVALENT OF A FENDER PRINCETON AMP WITH A 15 SPEAKER. IT WORKS AND SOUNDS GREAT. IT IS SURE TO MAKE SOME LUCKY EBAYER VERY HAPPY. IT IS INCLUDED IN THE S&H QUOTES. The item “RARE VINTAGE 1959/1960 USA GIBSON INVADER TWEED TUBE GUITAR AMP AMPLIFIER L@@K” is in sale since Wednesday, December 9, 2020. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “maconmusic” and is located in Macon, Georgia. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Singapore, Switzerland, Norway, Saudi arabia, Ukraine, United arab emirates, Qatar, Kuwait, Bahrain, Croatia, Malaysia, Chile, Colombia, Panama, Jamaica, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Pakistan, Paraguay, Reunion, Uruguay, Costa rica, Trinidad and tobago, Guatemala, Honduras.

• Number of Channels: 1
• Number of Speakers: 1
• Product Line: Gibson Invader
• Amplifier Technology: Vacuum Tube
• Power: 12-15 Watts
• Amplifier Type: Combo
• Brand: Gibson
• Suitable For: Acoustic Electric Guitar

VINTAGE NATIONAL WESTWOOD MODEL N 6422TR TUBE GUITAR COMBO AMPLIFIER AMP MADE IN THE U. WITH REVERB & TREMOLO. Estimated to be a 1965 model. The amplifier is working and sounds great! Also shows some new upgrades: New three prong plug and new speaker wire with extra length. Condition : There is tolex damage on the bottom, but it’s structurally sound. Front grill material shows wear and some of the side material is separating. Please see photos carefully. There are some good YouTube videos demonstrating this model amplifier. Note: This vintage amplifier is 50 to 60 years old, it may need some service, calibration or repair. Dimensions: 14.5″ High X 19″ Length X 8 Wide. The item “VINTAGE NATIONAL WESTWOOD MODEL N6422TR TUBE GUITAR AMPLIFIER AMP REVERB TREMOLO” is in sale since Tuesday, December 8, 2020. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “raineysrefinedremnants” and is located in Cerritos, California. This item can be shipped to United States.

• Number of Speakers: 2
• Model: Westwood Model N 6422TR
• Country/Region of Manufacture: United States
• Product Line: National
• Amplifier Technology: Vacuum Tube
• Amplifier Type: Combo
• Brand: National
• Suitable For: Electric Guitar

Gretsch Vintage 6161 Country Gentleman Tube Amp. 1959 Gretsch 6161 amp in excellent condition. Clean bill of health and updated 3 prong cord from Skip Simmons. Played indoors, no smoke. Ships insured, bubble wrapped with formed packing foam in dual ply cardboard box. FED EX Saver for US. If you have any questions, just reach out directly. Listing and template services provided by inkFrog. The item “Gretsch Vintage 6161 Country Gentleman Tube Amp” is in sale since Wednesday, December 2, 2020. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “ligyshka” and is located in San Francisco, California. This item can be shipped to United States, all countries in Europe, Canada, Mexico, Japan, Australia.

• Brand: Gretsch
• UPC: Does not apply

Knight Allied 10 Watt Mono Tube Amp Amplifier 6V6GT Vintage 1950s Tubes Tested PROJECT. Vintage Allied Radio Knight Kit mono 6V6 10 Wall Hi-Fi amp. Appears to be all original. Please see photos the power transformer, output transformer, tubes, wiring all appear to be original at least largely. The 6 tubes are. 6SL7 preamp, pair 6SN7preamp, 5Y3 rectifier, and a pair of 6V6 output tubes. Allied Radio / Knight. 10 Watt Hi-Fi Kit. Overall all unit NOT tested. Almost certain that some caps would be out of spec (after 70 years). Ready for your tender love (and servicing)! Background from the Radio Museum. 10 Watt Amplifier S-753. 10 Watt Amplifier S-753, Allied Radio Corp. (Knight, Roamer, Wextark); Chicago (IL). United States of America (USA). 5: 6SN7GT 6SN7GT 6V6GT 6V6GT 5Y3GT. Power type and voltage. Alternating Current supply (AC) / 117 Volt. This model requires external speaker(s). Metal case, Tubes Visible. 13 x 7 x 6 inch / 330 x 178 x 152 mm. The Allied Knight S-753 is a 10 watt amplifier with a response of 30 to 20,000 cps. It was available as a kit and a metal enclosure, S-757, and a preamp kit, S-235, were optional. The Preamp Kit (S-235) added a 6SL7GT preamp tube. Although this 10-watt Knight kit was produced for many years, model S-753 was specific to the chrome plated chassis variant which was available between 1956 and 1958. Other variants had a painted chassis, colors varied by year. Net weight (2.2 lb = 1 kg). 14 lb (14 lb 0 oz) / 6.356 kg. Price in first year of sale. A rescue from an estate in metro Detroit Michigan. Interesting vintage/estate items that were too nice to trash or give to a rummage sale. I want/hope they find new homes with appreciative owners/collectors. And by no means an? In books, silver, ceramics, comic books and so forth. So while I try to describe them in some detail and provide representative photos you will not see them with specific condition grades. Most of these items are used, vintage, so some wear is to be expected. Again, if I can detect any specific damage or repairs I will note them; my tendency is to emphasize negative condition issues. See item description for calculating cost. For very small or light-weight items (or very heavy), non-priority may be investigated as alternatives. Most of the time I will? Determined by the weight and distance. The item “Knight Allied 10 Watt Mono Tube Amp Amplifier 6V6GT Vintage 1950s Tubes Tested” is in sale since Monday, December 7, 2020. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “theworldsgoods” and is located in Farmington, Michigan. This item can be shipped to North, South, or Latin America, all countries in Europe, all countries in continental Asia, Australia, New Zealand.

• Brand: Knight – Allied
• Country/Region of Manufacture: United States
• MPN: 10 Watt Amp

Ask any amp aficionado which amplifier led the rock revolution, and you’ll get a near-unanimous response: the Marshall 1959 Super Lead. The Studio Vintage takes that legendary tone and packs it into a 20-watt combo. Plug in, and you’ll experience saturated blues grit and biting leads – the iconic Plexi tone. The Studio Vintage has plenty of player-friendly features on tap, such as four separate inputs, high- and low-sensitivity loudness controls, a 3-band EQ with Presence control, an effects loop, and a DI output. Worried about disturbing your neighbors? Don’t – the Studio Vintage’s power reduction circuit takes its wattage down to a bedroom-friendly five watts. If you want cranked Plexi tones from a compact, studio-sized amp, Marshall’s Studio Vintage absolutely nails it. 1×10 1-channel Tube Guitar Combo Amplifier with Celestion Speaker. High/Low Sensitivity Loudness Controls. The item “Marshall Studio Vintage Series 20 Watt All Valve Plexi Amp Head SV20H Tube Combo” is in sale since Thursday, November 12, 2020. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “overstocked-liquidations” and is located in Silver Creek, New York. This item can be shipped to United States.

• Brand: Marshall Amps
• Amplifier Type: Head
• Manufacturer: Marshall
• MPN: SV20C
• UPC: 5030463491003

Vintage Magnatone Troubadour Tube Guitar amp project Amplifier. The item “Vintage Magnatone Troubadour Tube Guitar amp project Amplifier” is in sale since Sunday, October 27, 2019. This item is in the category “Musical Instruments & Gear\Vintage Musical Instruments\Vintage Guitars & Basses\Guitar Amplifiers”. The seller is “toneahaulix” and is located in Fort Wayne, Indiana. This item can be shipped worldwide.

• MPN: Does Not Apply
• Brand: Magnatone

NEW Dynaco 70 / Dynakit Stereo 70 – 6GH8A TUBE VERSION. This Listing is for. Custom Built by Funtastic Vintronics. These are brand new amps – 100% – not a rebuild or a restoration – read the details. Enjoy the rich smooth tones of analog audio and even order harmonics that only vacuum tube amplification can produce. It reveals musical qualities with fantastic realism and depth you may have never imagined possible. The legendary original design up to date with highly improved levels of sound quality, looks and performance. Because of the ST-70′s naturally high impedance (470K) it is compatible with virtually any solid state or tube preamp. This amplifier puts out 70 watts total, 35 watts per channel. It is fairly safe to say that most people today would have no idea of how wonderful a Stereo 70 amplifier is capable of sounding like. “Original condition” amps or those “updated” or having any number of “modifications” from mild to wild can still leave a lot to be desired. “Restored” is more than popping in a few capacitors and some tubes. Much more will need to be done to fully bring about that great sound the amp once had. Although they will play music, they are still incapable of reproducing the sound quality they possessed when new, 50 years ago unless they are fully restored. Resistors become noisy and drift out of tolerance due to age and heat. Circuit board and component materials begin to deteriorate causing signal degradation, solder joints and tube sockets can be loose, oxidized, worn and have poor quality connections causing signal interference and noise. Capacitors lose their range and clarity, their values having changed with time. Hiss, buzz, hum, pop and fuzziness are not normal or desirable qualities. Isn’t the great smooth sound of a time long gone by what you’re really after, those sweet tones produced only from tube amplification? Like a musical time machine, this amplifier will take you back to the beginning, like when these amps were new. But there’s even more to consider here. All of the components used in this amplifier have greatly improved characteristics over the ones available and used 50 years ago. That makes the sound quality of this amp even better than one would have been then, as a new one 50 years ago. Take a good close look at this one. Don’t cheat yourself out of what you’re really wanting; superb sound, high build quality, safe and reliable operation, great looks and that comforting pride of ownership. Mundorf MCap ZN Capacitors – 600v – 5% – Values are increased to. 1uf for Improved Bass Response. 1% Accuracy Ultra Low Noise. 70 Watts Total Output – 35 Watts Per Channel – Pure Real Analog Power. Genuine Dynakit PC-3 “B” Circuit Board – Made Specifically for 6GH8A Driver Tubes – No tube Adapters here. Includes (2) tightly test matched Vintage NOS 6GH8A Tubes by RCA or GE (as per availability). Includes (4) New EL34 / 6CA7 NessTone Output Tubes – Plate Current Matched – Amazing Sound. Includes (1) New 5AR4 / GZ34 Rectifier Tube – Groove Tubes Label – Soft Start – High Current Capability. Bias Circuit uses 100uf Capacitors with Flameproof Metal Oxide Resistors. Dynakit PA-060 Power Transformer (120v Windings) – Notice its Size, the Increased Lamination Stack! Dynakit A-470 Output Transformers – (4,8,16 Ohm Taps) – Grain Oriented Laminations – Interleave Wound. Dynakit C-354 Shielded Power Supply Filter Choke – (1.75 Henries, 62 Ohms, 10%) – No More Nasty Leaks. 9 Brand New High Quality Tube Sockets. 600v & 1000v Wiring Used Throughout the Entire Amp. Genuine Dynakit Multi Section Filter Capacitor – Factory Correct Values 80/40/30/20uf – 525v Rated. New Dynakit Stainless Steel Mirror Finish Chassis (Non-Magnetic) – Beautiful Museum Quality Look. Brand New Dynakit Perforated Steel Cover w/ matching badge. Power Supply has Diode Rectification – No Scary Old Outdated Selenium Rectifier Here! Flashback Prevention Safety Diodes Installed at the Rectifier Tube. Additional shielding on under chassis components to reduce EMI / interference. Careful wire routing to reduce movement & electromagnetic signal interference (EMI). Assembled With Alpha Fry 60/40 rosin core solder – for the Very Best Quality Connections. Power Transformer Isolation Bushings Installed – Prevents the Transfer of Mechanical Hum to the Chassis. Custom Silver RCA Input Jacks – Wider Spacing for Larger Modern Input Cables. Original Screw Style Speaker Output Terminals – Vintage Correct – Full Function (4,8,16 Ohm + Common/Ground). Heavy Duty Rubber Feet with Steel Bushings. New 3 wire grounded power cord. Assembled with Great Attention to Detail Using High Quality Parts – 48 hr Minimum Burn in Tested – Sounds Incredible. Operates From a Standard Wall Outlet – No Voltage Reducer or Variac Needed – Built for Today’s 120v+ Voltages. Arrives With Bias Preset. Just Install the Tubes – Simple To Do – Instructions are Included. Front Preamp Sockets are Wired for Bias Set Only – Reduces Audio Signal Interference. The photos seen here are of several different amplifiers, meant to provide an example of the units offered for sale. Yours will look like the ones in these photos. Vintage Vibe – Modern Reliability – The Beautiful Sound of Tubes. So how does it sound? Magical – very musical with a highly detailed voice and plenty of solid, clean wonderful bass. This amp is absolutely dead quiet – no hum, no buzz, no hiss, no snap-crackle-pop! It sounds like it is supposed to. If you’re in search of that golden age of audio sound with stunning vintage looks, you’ve just found it. This is your bad boy. This is a 100% brand new amp, a very high quality build, total listening satisfaction. This ST-70 delivers dramatically improved sonics as the result of being carefully and thoughtfully built, all new, from the ground up, with technologically advanced components and all high-end parts. Is used with only a couple of re-engineered elements on the PCB traces to accommodate the 6GH8A tubes without having to use an adapter. Pay particular attention to the size (height) of the power transformer on this amp (the middle one). Transformers are the heart and soul of a tube amp, period. Dynaco wasn’t messing around when they designed and built their originals. Notice how tall this new transformer is compared to the original Dynaco PA060 power transformer. This is a real case of bigger is better. These new Dynakit transformers were reverse engineered from the original Dynaco designs using modern technologies and insulations. An increased lamination stack on this power transformer allows it to run cooler and provide better regulation. These transformers wont buzz or hum like the originals often do either. A major factor to consider here too is that the original transformers were designed to run from yesterday’s 117 Volt household current. Today’s household current is often 125 Volts or more so the use of a “step down” or “bucking” transformer is necessary to retard the voltage down to a safe operating level for amps having the original transformers. The new transformers are made for today’s higher household currents or VAC (Voltage). These transformers can be operated directly from your household outlets without secondary devices needed to reduce the voltage. These are USA made transformers that meet and exceed every aspect of the originals. If there were some sort of “magic” in the use of cloth leads, Dynakit would have certainly insisted on using them again. There’s simply no magic in cloth covered lead wire, period, it is inferior. In any comparison, these new transformers are just better than those old originals. Modern advancements in materials, methods and technologies used in the production of these transformers has resulted in superb transformers that operate quieter and cooler than the originals while providing less distortion, more power with increased reliability. The new A470 output transformers are also greatly improved, like the power transformer. The output transformers are interleaved/layer-wound and incorporate high quality M-6 grain oriented laminations. These also use better quality wire with better insulation, the primary is wound the same as the original A470 using the same number of turns on the same number of sections. These are made using the same patented Dynaco winding method, and made on the same core size and material type as the originals. These transformers are in one word, exceptional. I have selected the Groove Tubes 5AR4/GZ34 as the rectifier tube in my Dynaco 70′s for more than 2 years now. It has the highest current capability and has been 100% reliable, it also looks right in the amp. I believe it to be the best current production rectifier tube of its type on today’s market. Same story for the NessTone EL34/6CA7 tubes, they’re all I use now. These output tubes are hand selected and tested here in the USA and then identically matched as a quad (4 tubes) by their plate current test. Results using the ROE computerized testing system. I have had nothing but satisfied buyers and zero failures, they sound amazing. This amp also comes with 2 NOS RCA, GE or similar (as per availability) 6GH8A tubes, tested and matched. The 6GH8A like the 7199 tube is a vacuum tube combining both a pentode and triode in a single glass envelope. Each section has a separate cathode and is electrically independent, the pentode is used for the input stage, and the triode as a phase inverter. The Dynaco ST-70 Series II came from the factory with a 6GH8A driver board and tubes. According to Dynaco published research and literature the 6GH8A tube actually outperformed the 7199! I also offer this amp in a 7199 version, identical in build with the exception of the 7199 driver board and tubes. The photos show the ST-70 using the updated Dynakit PC-3 board made for 6GH8A tubes. Amplifier makers like HH Scott, Harman Kardon and Eico, among others, have used the 6GH8A since back in the late 50′s. I honestly find no audible difference in the 7199 and the 6GH8A so long as both tubes are of equal quality. Good quality tubes are essential for the overall sound quality simply because they are a part of the circuit, the circuit can only sound as good as it’s parts will allow. Good circuit design is critical, the Dynaco circuit is genius. The 6GH8A, also no longer in production, appears to be in abundant supply and is very affordable. Like all tubes, some brands and build styles offer both sonic and reliability advantages over cheaper, inferior made tubes. This amp comes with 2 NOS RCA, GE or a Mullard variant (as per availability) 6GH8A tubes, tested and matched. Contact me if you want the 7199 version, I’ll make a special listing for you. Manuals, Instructions, pictorials, diagrams, schematics and supplemental documentation are all included on a CD-Rom. Tube installation instructions with a numbered easy to follow pictorial included. Bias will be pre-set but due to variations in AC wall voltages the bias should be checked and adjusted for your specific location. Each unit is custom, a hand built, made to order unit. Your unit will look identical but wire color and routing may be slightly different from unit to unit, these are hand built units. Turnaround time is running 4-5 weeks right now. Straightforward simple business here. The manuals, instructions, pictorials, diagrams, schematics and supplemental documentation are all included on a CD-ROM. Issues from abuse, misuse, neglect or external damages are not covered. Damage from moisture of any kind, electrical surges, lightning and static electricity are not covered. Coverage is limited to replacement of any original components which have failed under normal operating conditions. Faulty components will be replaced with no charge to you. For parts or labor. The item “Dynaco Dynakit ST-70 Stereo Tube Amplifier, New, Not Vintage EL34 Push Pull Amp” is in sale since Friday, December 4, 2020. This item is in the category “Consumer Electronics\Vintage Electronics\Vintage Audio & Video\Vintage Amplifiers & Tube Amps”. The seller is “had-fun-moved-on” and is located in Coweta, Oklahoma. This item can be shipped to United States.

• Model: Dynakit Stereo 70 / ST-70
• Modified Item: No
• MPN: DYNAKIT Stereo 70 / ST-70
• Country/Region of Manufacture: United States
• Custom Bundle: Yes
• Brand: Dynaco
• Included Tubes: (2) 6GH8A – (4) EL34 / 6CA7 – (1) 5AR4 / GZ34
• Type: Tube Amplifier
• Bundle Description: fully assembled amplifier with cover and all new tubes

Up for sale, a 1967 Fender Vibro Champ, freshly serviced, very original, and extremely clean cosmetically. This little Blackface-era Fender wonder delivers five watts of pure Class A tube tone. A surprisingly loud amp with the original alnico 8 speaker, this Vibro Champ has just the right amount of glassy, sparkling clean tone before pushing into smooth, lightly compressed tube overdrive at about 4 on the volume knob. Dynamic, responsive, and absolutely huge sounding when you put a microphone in front of it, it’s hard to beat the Vibro Champ for pure simplicity and great tone. And of course, Fender’s lush sounding tremolo circuit has a strong pulse and wide range of speeds, perfect for subtle shifts in volume or machine gun chop. The circuit is very original, with only a few new Sprague electrolytics and a couple substituted resistors in the preamp to keep the amp operating optimally. The stock Schumacher-made transformers date to the 27th and 46th weeks of’66, and visible date codes on the CTS pots date to the 15th week of’66. The tube chart is intact with a “QD” code which translates to April of 1967. The tube compliment includes a JJ 6V6 power tube and matching preamp tubes, with a vintage RCA 5Y3 rectifier. The speaker is the original Fender-branded Oxford 8 with a clean blue Fender label on the alnico magnet and date stamp from the 25th week of’66 on the edge of the frame. The original smooth black tolex and silver sparkle grillcloth are extremely clean, with plenty of sparkle in the thread and limited aging of the cloth. The faceplate is stunningly well-kept too, complete with its full compliment of witch hat knobs. The stock handle caps, sphinx glides (feet), and chassis straps are all intact, and the hardware shows sparingly little surface patina. This Vibro Champ is an ideal example of Blackface tone that sure to delight both discerning collectors and serious players. Check out our shop “Mike & Mike’s Guitar Bar, ” and please let us know if we can answer any questions! International orders will be declared as merchandise, and the value of merchandise will be declared as the amount paid. We cannot declare anything as a gift or for a lesser value. We do our best to describe all items with honesty and accuracy, but to be sure, please. The item “1967 Fender Vibro Champ Vintage Blackface Tube Amp Class A, Serviced” is in sale since Saturday, November 7, 2020. This item is in the category “Musical Instruments & Gear\Guitars & Basses\Guitar Amplifiers”. The seller is “mmguitarbar” and is located in Seattle, Washington. This item can be shipped worldwide.

• Number of Channels: 1
• Number of Speakers: 1
• Model: Vibro Champ
• Country/Region of Manufacture: United States
• Amplifier Technology: Vacuum Tube
• Power: 5
• Amplifier Type: Combo
• Brand: Fender
• Suitable For: Electric Guitar

Retro Gear Shop is a high-end boutique store located in Nashville, Tennessee. Fender Harvard Combo Amp 1960 For sale is a rare vintage Fender Harvard guitar tube amplifier. Incredibly clean condition for its age. Excellent shape, fully functional. Hard to find them in this nice of shape. Sounds fantastic, came from a private collector, was seldom used. More likely to continue to appreciate in value over time being so clean. You aren’t likely going to find a nicer one for sale, if you have been looking for a good one this is it. Don’t miss out! Check out the pictures to make sure you like it. Any questions please ask! The item “Fender Harvard Rare Vintage Amp Guitar Tube Amplifier 1960″ is in sale since Wednesday, December 2, 2020. This item is in the category “Musical Instruments & Gear\Vintage Musical Instruments\Vintage Guitars & Basses\Guitar Amplifiers”. The seller is “retrogearshop” and is located in Nashville, Tennessee. This item can be shipped worldwide.

• Model: Harvard
• MPN: Does Not Apply
• Brand: Fender