Vintage Organ Tube Amplifier. To use the gearhead expression “ran when parked”, it did work before I put it storage. As you can see, storage has not been kind to it. This unit has 1x 5U4GB Rectifier, 4x 6BQ5 / EL84 power tubes and 4x 12AX7 tubes. This amplifier is a prime candidate for a sweet little conversion project! The last 2 picture are from Worthpoint to show you what this looks like shined up. This is in Louisville, Kentucky.
The US made GE 6L6GC is one of the best classic 6L6 tubes ever made. US Made 6L6GC are getting harder and harder to find – especially in a condition this pristine. Right up there with later production RCA, these tubes can handle the voltage and deliver the tone you are looking for. These 6L6GC have the side getters and sound fantastic.
Outstanding Vintage 62′ Hammond Power Amplifier H-AO-29-13 With Its individually Tested Tubes. From a fully functional and well maintained model M-111, fully tested before carefully removing. The following are the test values for each tube. 5U4 : 94/94 (94%/94% of NOS). 6BA6 : 95 (95% of NOS). 6V6 : 97 (94% of NOS). 6V6 : 94 (94% of NOS). 12AX7 100/100 (100%/100% of NOS). 12AU7A 95/95 (95%/95% OF NOS). 6AUA 95 (95% of NOS). 6AUA 100 (100% of NOS). 6C4 100 (100% of NOS). 12AU7A 94/95 (94%/95% of NOS). The power cord has a lot of cracking and fraying. It will need replaced. The black tape was placed just for testing. Feel free to message any questions.
Note: Price is for the pair of RCA monoblock amps as pictured. From my personal collection. RCA Tube Monoblocks MI-9377A updated! Coke bottle vintage 6L6s! Lightly updated with new caps and speaker posts, power switches. One amp has replaced power transformer that looks similar but not identical to original. Ugly front panels removed (no original front panels included) to reveal very pretty amps. Cosmetic: Good with some scratches, small dings etc. Will be securely double-boxed with tubes labelled and removed for safe travels.
38 NOS NIB 12AL5 NOS NIB TUBES MADE BY RCA BRANDED UNITED. YOU GET THEM ALL. EACH TUBE IS 100% BRAND NEW OLD STOCK. HIGH GRADE 12AL5 / HAA91 TUBES FOR YOURE AMPLIFIER NEEDS. THIS LARGE COLLECTION IS 100% GUARANTEED. THE BOXES AND THE TUBES ARE ALL IN BEAUTIFUL SHAPE. YOU GET EVERYTHING IN THE PHOTOS FOR THE PRICE. HIGH QUALITY RCA MADE TUBES. MADE IN THE 1960′S IN THE USA.
This Listing is for a Pair of Vintage RCA MI-12222 Mono Tube Amplifiers Read Description. One has a intermitted power switch and one is microphonic (when you tap on the amp you can hear it through the speaker). They have been reworked but no further testing has been done. TUBES ARE NOT INCLUDED Please refer to all photos for more details as they are the best part of the description. Pair of Vintage RCA MI-12222 Mono Tube Amplifiers Read Description No Tubes. Check out our entire store for more great products and deals! We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers.
McIntosh MC240 Vintage Tube Amp – SkyFi Restored w/Premium Vintage Tubes. General: We painstakingly restored this classic and coveted stereo tube amplifier to its full glory. Internally we replaced every critical component while carefully maintaining the original sonic quality. This listing also includes a rare and correct McIntosh tube cover (tube cage). SkyFi Restoration Notes: This MC240 underwent an extensive electronic restoration in house. The electronic work included a full rebuild of the power supply using custom made multi-section capacitors that match the exact values and layout of the original power supply. The bias supply was also rebuilt with new parts. The selenium bias diode was swapped to silicon with proper adjustment resistor to maintain the ideal bias level for the unity coupled output section. We also replaced all of the paper and di-film capacitors in the signal path after finding them leaky and drifted. During the signal path capacitor replacement we checked all of the resistors and replaced any parts that had drifted out of tolerance. By default we replace the phase inverter balancing resistors and plate load resistors with precision metal film parts to ensure trouble free performance. To finish up, we replaced the power cord and inrush current thermistor. Tube Notes: This amplifier is fitted with a set of premium vintage tubes. The output tubes are RCA 6L6 (2) are labeled McIntosh at the base. All four are RCA made tubes. The two labeled RCA have brown colored getter flashes but still test strong and sound great! The 12BH7 are strong matched and balanced GE. The remaining tubes are all strong testing authentic Telefunken 12AX7 and 12AU7. Cosmetic Notes: This MC240 was well loved. It has moderate chrome pitting and light silkscreen wear which is common for McIntosh amplifiers from this era. There are also some scratches/markings on the black transformer covers and cage. Two historic Dave O’Brian clinic stickers flank the McIntosh 240 badge and show years 1971 and 1972. The company was founded in 1949 by Frank McIntosh. The company designs and produces audio amplifiers, stereo tuners and other consumer electronics products. Ownership: Unknown Connections: RCA Inputs, Screw Terminal Outputs General Sound: Smooth, uncolored, undistorted natural and clean Cosmetic Condition: 6 / 10 Working Condition: Working perfectly and tested in our lab and listening room. Included: Unit, power cord, manual, and tube cage. Packing: Will be packed using our highly developed in-house process and custom packing materials. Specs: Power output: 40 watts per channel into 8? (stereo), 80 watts into 2? (mono) Frequency response: 16Hz to 40kHz Total harmonic distortion: 0.5% Input sensitivity: 0.5V Signal to noise ratio: 90dB Speaker load impedance: 4? Tube complement: 1 x 12AX7, 2 x 12AU7, 2 x 12BH7, 2 x 12AX7, 4 x 6L6GC Dimensions: 17-1/4″ x 10-3/4″ x 8 Weight: 56 lbs. Testing Process: The SkyFi Testing Process for Tube Amplifiers: We start with a visual inspection of all internal components to make sure that there are no signs of heat stress or damage. Capacitors are checked for telltale signs of predictive failure including bulging, shrunken wrappers, or physical leakage. We also inspect resistors and other passive components for signs of overheating. If tube arcing has occurred in the past we can usually spot discoloration on the output tube sockets. On vintage units we often spot check select capacitors for value and ESR. If the amplifier passes visual inspection, we move on to a full test of all of the tubes. We use an Amplitrex AT-1000 Tube Tester which is capable of testing both emission and Gm with a high degree of accuracy. We document the results of each tube and replace any weak or suspect tubes before proceeding. When we power on tube amplifiers for the first time we usually use a variac and current limited AC supply and slowly raise the voltage up to nominal mains level while monitoring plate, screen, filament, and negative bias supply voltages where applicable. If everything is in order we feed a low level test signal into the amplifier’s input and monitor its output on an oscilloscope across an 8 ohm dummy load. At this point we are just looking to verify basic function and confirm that the output transformers are not damaged. Once we have verified that the amplifier is safe to operate, we connected it to full mains power. For cathode biased amps we monitor the plate to cathode voltage to determine if the output tubes are operating in a safe range. Once the output section is verified we move onto bench evaluation. We start by feeding the input of the amplifier with a low level 1KHz test signal, slowly increase its amplitude while monitoring the amplifier’s output on an oscilloscope for signs of noise, clipping, distortion, or improper channel balance. We continue increasing the signal level until the amplifier reaches clipping. At this point we take an output power measurement and compare it to the spec sheet of the amplifier to verify proper performance. We finish off the bench evaluation with a 1KHz square wave check and a 20Hz to 20KHz sine sweep to assess the amplifier’s frequency response characteristics. This battery of tests will usually reveal if the amplifier has any issues that need further attention. Before the device leaves the bench, we perform a listening test with actual music using a variety of preferred test tracks. Our benches are outfitted with familiar monitor speakers which help us identify inconsistencies that will not always show up on our test gear. The main things that we are listening for are hum or noise with no signal present, proper center image, clicks, pops, or any other obvious undesirable audio characteristics. If the unit passes all of these tests it is moved to our long term testing rig where we simulate real word operating conditions for 6-8 hours. For tube amps we like to run this test at least twice. This allows us to monitor the unit for signs of thermal runaway or intermittent issues that only crop up when it has fully come up to temperature. We find this step to be essential, especially for vintage units. Please note we are not a repair shop and only restore what we own. SkyFi Audio – Curators of Vintage Audio Gear. No mid-fi, no gimmicks, no junk. Each piece of equipment is cosmetically restored and fully tested in our well-equipped lab by an engineer with 30+ years of experience in the HiFi world. Through our sister company, which is an authorized dealer for McIntosh, Audio Research, Sonus Faber, ClearAudio, Project, and Sony ES, we have access to OEM parts, service, and support. If we don’t have the original packaging, we use heavy-duty double-ply corrugated boxes with custom made to your item SealedAir Instapak expanding foam custom inserts. In many cases this has proven to be better than the original packaging! We also use high quality fiber reinforced tape to seal our packages. We have too many items for sale and it’s nearly impossible to keep track of offers outside of the official system. Our items are available for pick-up. No additional information at this time. You might also like. Dynavector 10×3 High-Output MC Phono Cartridge. Mcintosh MC2500 Solid State Amplifier – In Silver Finish! Music Reference RM-5 MK II Tube Preamplifier with Phono. Music Reference RM-9 Tube Amplifier With EL34′s.
These are the Holy Grail Y’all – a perfectly matched strong pair of 60+ years old Black Plate RCA 6L6GC’s. Privately labeled for Baldwin. The tubes’ test results are displayed in the photos (New 6L6 Spec 100% =6,000 Gm). See the photos for physical / cosmetic condition. Notes Regarding Tube Tests. All tubes are tested on an Amplitrex AT-1000 tester in the automatic Fixed Bias Mode (for the most conservative results). Test Results are for a general reference only, and are not a guarantee of performance, nor a guarantee of how they will test on your tester. No real world (audio) performance measurements are taken.
This Listing is for a Vintage Heathkit SP-2 Stereo Preamp Pre-Amplifier 12AX7 Tubes. This is in pretty good condition. Tested and it plays well. Some of the pots are just a bit scratchy, could use a good cleaning. It is missing the feet and one of the screws is bent a little. Please refer to all photos for more details as they are the best part of the description. Vintage Heathkit SP-2 Stereo Preamp Pre-Amplifier 12AX7 Tubes. Check out our entire store for more great products and deals! We do however make every possible attempt to accurately describe the inventory we sell and stand behind it. Since 2016, 8TEN Industries has been a leading asset recovery provider supporting national retailers, brands, and manufacturers. Our 60,000 square foot processing and distribution facility located in Cass City, Michigan has allowed us to become industry leader in turning difficult problems for manufacturers into great deals for our customers.
This particular set is the same as the 3-hole military VT-231 version, and tests strong. Special care was taken not to rub off any of the print while testing. The tubes’ test results are displayed in the photos (New 6SN7 Spec 100% = 2,600 Gm). See the photos for physical / cosmetic condition. Notes Regarding Tube Tests. All tubes are tested on an Amplitrex AT-1000 tester in the automatic Fixed Bias Mode (for the most conservative results). Test Results are for a general reference only, and are not a guarantee of performance, nor a guarantee of how they will test on your tester. No real world (audio) performance measurements are taken.
